11-29-2018, 04:06 PM | #1 |
BMW obsessed
9580
Rep 10,875
Posts |
IND | G05 X5 Painted Front Reflector | Installation Procedure
GENERAL NOTE: This method was created for a true garage DIY with minimal intrusion to OE equipment. The proper method would require a much more comprehensive set of instructions and additional tools (rivet gun, etc).
Step 1: Start the vehicle and turn the wheel to the opposite side of which you intend to work. This will grant you easier access to the fender liner. Step 2: Remove the two 8mm fender liner bolts aft of the reflector and pull the liner loose. Step 3: Carefully pop the painted fender arch from its housing. There is no need to remove this piece completely; where the front bumper meets the fender is good enough. Step 4. Use a heat gun to apply uniform heat the OE reflector. This will soften the adhesive that holds the reflector in place. Please take note to keep the heat gun moving during this process to ensure no paint damage (burning) occurs. Step 5: With the reflector area properly "warmed up", use your thumbs to depress the OE unit while using your other fingers to simultaneously pull on the surrounding bumper from the inside of the fender liner. We've found it easiest to work from the bottom first. Step 6: Once the bottom of the reflector is freed from the bumper, you may slide a bondo spreader between the fender liner or "outside in" and pull it upwards to help release the adhesive. Step 7: With the reflector now completely free, you will need to slide it out from the bumper. Pull the bottom of the reflector down and towards you. This will pivot the top of reflector toward the front of the car. From here, you are able to work the reflector out through the fender liner. NOTE: If you attempt to pull straight down instead of pivoting, it's likely that the + shaped retaining tab on the back of the reflector will get stuck on the plastic ducting element. Step 8: Occasionally, all of the OE adhesive doesn't come out with the reflector. If some adhesive still remains, take some time to remove it completely from the inside of the bumper. This will ensure a uniformly flat contact area for the IND reflector replacement. Step 9: Expose the adhesive on the IND painted reflector replacement. Step 10: Going from the "outside in", insert the IND reflector and position it properly. With uniform pressure behind the fender liner, adhere the IND reflector with the bumper. Similar to Step 5, you may also use your other hand to press the bumper edge forward creating a "sandwich effect" to ensure full adhesion. Step 11 (optional): Use a hand-held polisher to finish the front reflector. Step 12: Re-insert the OE fender arch trim, ensuring proper tab alignment prior to pushing it into place. Step 13: Re-fasten the fender liner and install the 8mm bolts removed from Step 2. Step 14: Repeat this procedure for the other side.
__________________
|
Appreciate
10
r33_RGSport12960.00 ncm5guy27.50 polychromatic134.50 Dagwag7752.00 Skilly40.00 iconoclast7265.50 boneca1999.50 Al Pinγ1839.50 MJBradley1967190.50 johnnyace57.00 |
11-29-2018, 05:06 PM | #2 |
General
12960
Rep 18,707
Posts |
Great work!!!
Much easier than F15/F16 F85/F86.
__________________
Email:sales@rgsport.com | IG:RGSport_USA | Web:RGSportShop.com PM for Everyday DEALS!! MSS iSweep RaceChip Sterckenn AutoTecknic Akrapovic Vossen Wheels Eventuri Active Autowerke KW H&R Ohlins Remus and more... |
Appreciate
0
|
11-29-2018, 06:39 PM | #4 |
First Lieutenant
146
Rep 342
Posts |
Awesome! Thanks for the installation guide and pics! I'm receiving mine in the mail tomorrow, about 3 weeks before the actual car arrives.
|
Appreciate
1
IND-Distribution9579.50 |
11-30-2018, 12:03 AM | #6 |
Captain
188
Rep 602
Posts |
Awesome. I already have mine sitting here and I don't eve have the X5 yet! LOL
When will you have the blacked out grille ready for sale? Please let me know ASAP!!! Thank you! |
Appreciate
0
|
12-04-2018, 01:52 AM | #8 |
First Lieutenant
146
Rep 330
Posts |
|
Appreciate
0
|
12-27-2019, 10:32 AM | #9 |
Second Lieutenant
211
Rep 274
Posts |
Just completed my install and it is much harder then it looks in this write up. The + tab on the reflector makes it very difficult to maneuver into position. I do not see how they could have gotten the reflector in place going outside in. There is just not enough room to wedge the reflector through the outside.
|
Appreciate
2
NYCX5M50i63.50 Flying Ace4984.50 |
12-27-2019, 06:40 PM | #10 | |
Captain
191
Rep 802
Posts |
Quote:
__________________
2020 X5 M50i | 2015 X3 28i xLine | Retired 2013 335i M Sport
|
|
Appreciate
1
vicfalc09211.00 |
12-27-2019, 09:08 PM | #11 | ||
Second Lieutenant
211
Rep 274
Posts |
Quote:
|
||
Appreciate
0
|
12-28-2019, 09:11 AM | #12 | |||
Captain
191
Rep 802
Posts |
Quote:
__________________
2020 X5 M50i | 2015 X3 28i xLine | Retired 2013 335i M Sport
|
|||
Appreciate
0
|
12-28-2019, 09:52 AM | #13 |
Enlisted Member
13
Rep 32
Posts
Drives: 2019 G20 330i M-Sport
Join Date: Feb 2019
Location: Laguna Niguel, CA
|
Just wonder is this legal in the USA to remove yellow reflectors?
|
Appreciate
0
|
12-28-2019, 10:20 AM | #14 |
Second Lieutenant
135
Rep 233
Posts |
Dunno, I changed out the orange to clear/white on my Carrera and M3, and no one noticed after multiple state inspections. Note these were relatively small reflectors compared to the X5s and I think the orange stands out more on white body color.
|
Appreciate
0
|
02-17-2020, 06:30 PM | #15 |
New Member
18
Rep 13
Posts |
I took a stab at this install today. I must say that I thought it was easier to do on my F15 given that there was more room to work with behind the fender. It took me over an hour for the first side and less than 30 minutes for the second. 2 time saving tips that I learned while working on the first side is to buy 2 rivets and remove the ones that hold an internal plastic liner tight against the fender. I have marked up the IND pic to show the rivet location. The second is when removing the fender flare, the bottom vertical tab actually points straight down on the inside so its best to bend it up from inside the fender liner and push it out from there. The other fender tabs after that are accessible by hand and are easy to get out once the bottom tab of free.
I have include pics of the before and after too (sorry they are sideways...). Overall I love the look these reflectors, much more than the small cuts on my hands so I'd say the time and effort was worth it. |
04-06-2020, 12:57 PM | #16 | |
New Member
2
Rep 12
Posts |
Quote:
So when you are talking about the "bottom vertical tab", which one do you refer to in the following pic (marked up from the IND pic)? A or B? As I did not see A in your pic. Also how did you get that done (bending tab A up from inside the fender liner and push it out from there)? Did you use any tools or fingers only? For tab B it seems that I have to either push it from the front bumper ventilation hole (2nd pic), or pull it from the gap behind the flare (3rd pic)? |
|
Appreciate
0
|
04-06-2020, 01:35 PM | #17 | |
New Member
18
Rep 13
Posts |
I was referring to the tab you marked as A. It is pointing down, if you bend it up (make it more horizontal) you can push it out of the slot. From there the tabs you have marked B can be be pushed out from behind. You should be able to see them . I trim tool would help but not required.
Quote:
|
|
Appreciate
0
|
04-06-2020, 02:45 PM | #18 | |
New Member
2
Rep 12
Posts |
Quote:
I notice that tab A has a hole. Does that mean it is secured with a screw or something similar? Or it is flexible to bend with fingers? Right, I can see tab B from either front bumper or from behind. Did not notice tab A yesterday and had a hard time fighting to push tab B out from the very beginning |
|
Appreciate
0
|
04-06-2020, 04:56 PM | #19 | |
New Member
18
Rep 13
Posts |
I don't remember there being anything securing the A tab. Once that is free the other tabs should be easier to get out. Good luck!
Quote:
|
|
Appreciate
0
|
04-10-2020, 06:09 PM | #20 |
Enlisted Member
37
Rep 46
Posts |
Love em!
|
Appreciate
2
IND-Distribution9579.50 NYCX5M50i63.50 |
06-26-2020, 12:27 PM | #21 |
Lieutenant
285
Rep 441
Posts
Drives: BMW
Join Date: Nov 2018
Location: in my bimmer
|
How do i remove the rivets? Do i need to push it in first or just yank n break it?
|
Appreciate
0
|
10-23-2020, 10:35 AM | #22 |
Self-Deprecating Narcissist
7266
Rep 6,561
Posts |
The most difficult portion of this install is the removal of any adhesive left behind from the previous set of reflectors. Outside of that it is fairly straightforward and much easier if you remove the plastic rivet.
__________________
|
Appreciate
1
Flying Ace4984.50 |
Post Reply |
Bookmarks |
|
|